Ronan X96S MASS FLOW GAUGE Manuel d'utilisateur Page 70
- Page / 77
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
66
X96-2008PL
X96-2008PL is the Digital Input/Output Module. The module provides a total of 16 bits of digital I/O and
wetting/encoder power.
8 isolated digital inputs are provided. These inputs can be configured for use as:
• dry
5
or live
6
contact monitoring,
• quadrature encoder
7
, or
• pulse counter.
4 relay (2 Amp capacity) output points are provided. Form “C” outputs are brought out to the connector
(three connections per relay).
4 isolated open collector output points are provided. These outputs are capable of switching 4.5 to 30 Volts
(externally supplied) at a maximum of 50 ma.
24 volts DC is provided for use as a wetting voltage when needed.
An isolated 15-volt DC power supply capable of providing 200 mA is also provided. The primary use of this
power supply is to power a quadrature encoder. However, it can be used for other purposes if it is not
required for this purpose.
X96-2009PL1
X96-2009PL is the Scintillation Detector Interface Module. This optional
8
module provides:
• 1 isolated scintillation input (pulse counter, max signal 0-12
9
V, threshold 0.6 V)
• 1 head temperature input (1 uA per deg K)
• 1 non-isolated RTD (3-wire) input
• isolated power for the scintillation detector 24 V 40 mA supply
10
.
5
When used with dry contacts, jumpers shall be used on the connector block to provide the wetting voltage. When used in this
mode, input to input isolation is not maintained.
6
When used with live contacts, each input shall be able to accept up to 30 volts DC. Zero volts to 0.8 volts are recognized as a
logic zero and 2.5 volts to 20 volts are recognized as logic one.
7
The interface to the quadrature encoder shall consist of two inputs, 15 volts DC at 200 mA (described in a later section), and
common.
8
At least one detector interface module is required.
9
8.6 V nominal.
10
The power supply has the ability to control the power to the scintillation detector:
• when commanded by the CPU module,
• when the processor on the module detects a condition that could harm the scintillation detector,
• when the watchdog timer generates a reset.
- MASS FLOW GAUGE 1
- Table of Contents 2
- Overview 5
- Basic Concepts 6
- Theory of Radiation Gaging 7
- Principles of Operation 8
- Menus/Operation 10
- [enable/disable] 11
- [Enable/Disable] 12
- [number] 12
- [seconds] Slot 2 12
- [type] Output 14
- Figure 3-4 Calibration Menu 15
- Figure 3-5 – Diagnostics Menu 16
- Variable Mapping Menu 17
- Status Display Menu 18
- Display Totalizer 19
- Operation Menu 19
- Density Filtering Menu 20
- Flow Rate Filter Menu 21
- Empty Clamp Menu 21
- Detector Fault Menu 22
- Temp Comp Menu 22
- Linearization Menu 23
- Scan Time Menu 23
- Mass Flow 23
- Solids Setup 25
- Flow Rate 25
- Proc Temp 25
- Head Temp 26
- Remote Totalizer Menu 27
- PD Counter 27
- Auto Reference 28
- Hardware 29
- System Hardware 29
- Source Type 30
- Next Shutter Test 30
- Flow Rate Hardware Menu 30
- Solids Adj. Hardware 31
- Analog Out Cnfg Menu 31
- HART Output 31
- Com1 Protocol 31
- Digital Outputs Menu 32
- Calibration 34
- Cal Remote Solids 34
- Ref Constants 35
- Low Reference (Cal Flow Rate) 36
- Temp Reference 37
- Loop Config Menu 37
- Aux Loop Cfg Menu 38
- Diagnostic 38
- X96S Local Display 40
- Editing Values 41
- Installation 42
- Handle Padlocked OFF 43
- Plunger Padlocked OFF 43
- Rod Padlocked OFF 44
- Lock Tag 44
- Safety Precautions 45
- Mechanical Mounting 46
- LOCAL CODE 47
- NATIONAL CODE 47
- Microprocessor Verification 48
- F1 F2 F3 F4 49
- Password 50
- Calibration Constant 52
- Calibration Curve 53
- Important facts to remember – 54
- Ronan Engineering 55
- X96S Mass Flow Gauge 55
- ABORT OK 56
- ESC ENTER 56
- High Density Calibrate 57
- Step 1 High Calibrate 58
- Low and High Flow Calibration 60
- Low Flow Reference 60
- (Have a “0” flow input ready) 61
- High Flow Calibration 62
- Configuration 64
- Detector 65
- ION Chamber 66
- Detector Housing 67
- Cable Connector 67
- Electronics 69
- X96-2009PL1 70
- X96-2009PL2 71
- X96-2009PL3 71
- MODEL X96S 73
- SAMPLE DRAWINGS 74
- Outline/Assembly 75
- Mounting Plate 76
- 21200 Oxnard Street 77
Produits connexes et manuels pour Équipement Ronan X96S MASS FLOW GAUGE
(3 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels