Ronan X96S MASS FLOW GAUGE Manuel d'utilisateur Page 18
- Page / 77
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
14
Status Display Menu
The Status Display menu is used to configure the device status display. It contains the following items
ITEM FUNCTION
Analog Bar Shows the current state of the analog bar display (enabled or disabled) and allows the
user change the state.
Line 1: Shows the data to be displayed on line 1 of the status display and allows the user to
change the selection.
Line 2: Shows the data to be displayed on line 2 of the status display and allows the user to
change the selection.
Line 3: Shows the data to be displayed on line 3 of the status display and allows the user to
change the selection.
Line 4: Shows the data to be displayed on line 4 of the status display and allows the user to
change the selection.
Line 5: Shows the data to be displayed on line 5 of the status display and allows the user to
change the selection.
Line 6: Shows the data to be displayed on line 6 of the status display and allows the user to
change the selection.
Line 7: Shows the data to be displayed on line 7 of the status display and allows the user to
change the selection.
Line 8: Shows the data to be displayed on line 8 of the status display and allows the user to
change the selection.
Lines 1 through 8 can select one of the following:
ITEM MEANING
Mass Flow Mass Flow (example: pounds per hour)
Density Density (example: pounds per gallons)
Flow Rate Flow Rate (example: feet per second)
Totalizer Totalizer (shows the accumulated flow)
PD Counter PD Counter (shows the current value in the predetermined counter)
% of Density Shows the percent of Density based upon the min and max Density range
% of Mass Flow Shows the percent of Mass Flow based upon the min and max Mass Flow range
% of Flow Rate Shows the percent of Flow Rate based upon the min and max Flow Rate range
Head Temp Head Temperature (if Available)
Proc Temp Shows the temperature of the process in Deg F, Deg C, Deg R, Kelvin
4-20 mA Shows the 4-20 mA output level
Raw Cnts Unfiltered counts (from scintillation detector) or raw analog measurement (from
ionization detector)
Filt Cnts Filtered counts (from scintillation detector) or filtered analog measurement (from
ionization detector)
Date & Time Current date and time
Tot Elapsed Time Shows the Total Elapsed Time since the last time Totalizer was reset
Diagnostic Selecting this option takes the user to the Diagnostic Menu
Not Assigned Blank line
- MASS FLOW GAUGE 1
- Table of Contents 2
- Overview 5
- Basic Concepts 6
- Theory of Radiation Gaging 7
- Principles of Operation 8
- Menus/Operation 10
- [enable/disable] 11
- [Enable/Disable] 12
- [number] 12
- [seconds] Slot 2 12
- [type] Output 14
- Figure 3-4 Calibration Menu 15
- Figure 3-5 – Diagnostics Menu 16
- Variable Mapping Menu 17
- Status Display Menu 18
- Display Totalizer 19
- Operation Menu 19
- Density Filtering Menu 20
- Flow Rate Filter Menu 21
- Empty Clamp Menu 21
- Detector Fault Menu 22
- Temp Comp Menu 22
- Linearization Menu 23
- Scan Time Menu 23
- Mass Flow 23
- Solids Setup 25
- Flow Rate 25
- Proc Temp 25
- Head Temp 26
- Remote Totalizer Menu 27
- PD Counter 27
- Auto Reference 28
- Hardware 29
- System Hardware 29
- Source Type 30
- Next Shutter Test 30
- Flow Rate Hardware Menu 30
- Solids Adj. Hardware 31
- Analog Out Cnfg Menu 31
- HART Output 31
- Com1 Protocol 31
- Digital Outputs Menu 32
- Calibration 34
- Cal Remote Solids 34
- Ref Constants 35
- Low Reference (Cal Flow Rate) 36
- Temp Reference 37
- Loop Config Menu 37
- Aux Loop Cfg Menu 38
- Diagnostic 38
- X96S Local Display 40
- Editing Values 41
- Installation 42
- Handle Padlocked OFF 43
- Plunger Padlocked OFF 43
- Rod Padlocked OFF 44
- Lock Tag 44
- Safety Precautions 45
- Mechanical Mounting 46
- LOCAL CODE 47
- NATIONAL CODE 47
- Microprocessor Verification 48
- F1 F2 F3 F4 49
- Password 50
- Calibration Constant 52
- Calibration Curve 53
- Important facts to remember – 54
- Ronan Engineering 55
- X96S Mass Flow Gauge 55
- ABORT OK 56
- ESC ENTER 56
- High Density Calibrate 57
- Step 1 High Calibrate 58
- Low and High Flow Calibration 60
- Low Flow Reference 60
- (Have a “0” flow input ready) 61
- High Flow Calibration 62
- Configuration 64
- Detector 65
- ION Chamber 66
- Detector Housing 67
- Cable Connector 67
- Electronics 69
- X96-2009PL1 70
- X96-2009PL2 71
- X96-2009PL3 71
- MODEL X96S 73
- SAMPLE DRAWINGS 74
- Outline/Assembly 75
- Mounting Plate 76
- 21200 Oxnard Street 77
Produits connexes et manuels pour Équipement Ronan X96S MASS FLOW GAUGE
(3 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.470 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels