Ronan X96S MASS FLOW GAUGE Manuel d'utilisateur Page 26
- Page / 77
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
22
ITEM FUNCTION
Temp Units Shows and allows the user to set the units to be used for process temperature
Low Range Shows and allows the user to set the temperature value to be mapped to 4ma on the
current loop output, if process temperature is selected to control that current loop.
High Range Shows and allows the user to set the temperature value to be mapped to 20ma on the
current loop output, if process temperature is selected to control that current loop.
Temp Units is one of the following:
ITEM MEANING
Deg C degrees Celsius
Deg F degrees Fahrenheit
Deg R degrees Rankine
Kelvin degrees Kelvin
Head Temp
The Head Temp Config menu is used to configure the parameters associated with the detector electronics temperature
measurement. This function is used primarily in high-temperature applications where the temperature exceeds the electronics
temperature specifications. It contains the following items:
ITEM FUNCTION
Temp Units Shows and allows the user to set the units to be used for head temperature
Low Range Shows and allows the user to set the temperature value to be mapped to 4ma on the
current loop output, if head temperature is selected to control that current loop.
High Range Shows and allows the user to set the temperature value to be mapped to20ma on the
current loop output, if head temperature is selected to control that current loop.
Temp Units is one of the following:
ITEM MEANING
Deg C Degree Celsius
Deg F Degree Fahrenheit
Deg R Degree Rankine
Kelvin Kelvin
Display Totalizer
The Display Totalizer menu is used to configure the parameters associated with the Display Totalizer. It contains the following
items:
ITEM FUNCTION
Totalizer Shows the accumulated mass flow in the Total Mass Flow register
Elapsed Time Shows the elapsed time since the last time the Totalizer was reset.
Totalizer Units Shows and allows the user to set the units to be used for the Totalizer.
Ext Reset Shows and allows the user to enable/disable the Totalizer to be reset remotely
Cutoff Shows and allows the user to set the minimum percent of material before totalization
occurs
Reset Totalizer Shows and allows the user to reset the Totalizer locally
Totalizer Units is one of the following:
UNITS MEANING
Ston Short Tons
LTon Long Tons
lb pounds
ounce ounces
MetTon Metric Tons
kg kilograms
ggrams
- MASS FLOW GAUGE 1
- Table of Contents 2
- Overview 5
- Basic Concepts 6
- Theory of Radiation Gaging 7
- Principles of Operation 8
- Menus/Operation 10
- [enable/disable] 11
- [Enable/Disable] 12
- [number] 12
- [seconds] Slot 2 12
- [type] Output 14
- Figure 3-4 Calibration Menu 15
- Figure 3-5 – Diagnostics Menu 16
- Variable Mapping Menu 17
- Status Display Menu 18
- Display Totalizer 19
- Operation Menu 19
- Density Filtering Menu 20
- Flow Rate Filter Menu 21
- Empty Clamp Menu 21
- Detector Fault Menu 22
- Temp Comp Menu 22
- Linearization Menu 23
- Scan Time Menu 23
- Mass Flow 23
- Solids Setup 25
- Flow Rate 25
- Proc Temp 25
- Head Temp 26
- Remote Totalizer Menu 27
- PD Counter 27
- Auto Reference 28
- Hardware 29
- System Hardware 29
- Source Type 30
- Next Shutter Test 30
- Flow Rate Hardware Menu 30
- Solids Adj. Hardware 31
- Analog Out Cnfg Menu 31
- HART Output 31
- Com1 Protocol 31
- Digital Outputs Menu 32
- Calibration 34
- Cal Remote Solids 34
- Ref Constants 35
- Low Reference (Cal Flow Rate) 36
- Temp Reference 37
- Loop Config Menu 37
- Aux Loop Cfg Menu 38
- Diagnostic 38
- X96S Local Display 40
- Editing Values 41
- Installation 42
- Handle Padlocked OFF 43
- Plunger Padlocked OFF 43
- Rod Padlocked OFF 44
- Lock Tag 44
- Safety Precautions 45
- Mechanical Mounting 46
- LOCAL CODE 47
- NATIONAL CODE 47
- Microprocessor Verification 48
- F1 F2 F3 F4 49
- Password 50
- Calibration Constant 52
- Calibration Curve 53
- Important facts to remember – 54
- Ronan Engineering 55
- X96S Mass Flow Gauge 55
- ABORT OK 56
- ESC ENTER 56
- High Density Calibrate 57
- Step 1 High Calibrate 58
- Low and High Flow Calibration 60
- Low Flow Reference 60
- (Have a “0” flow input ready) 61
- High Flow Calibration 62
- Configuration 64
- Detector 65
- ION Chamber 66
- Detector Housing 67
- Cable Connector 67
- Electronics 69
- X96-2009PL1 70
- X96-2009PL2 71
- X96-2009PL3 71
- MODEL X96S 73
- SAMPLE DRAWINGS 74
- Outline/Assembly 75
- Mounting Plate 76
- 21200 Oxnard Street 77
Produits connexes et manuels pour Équipement Ronan X96S MASS FLOW GAUGE
(3 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.851 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels