Ronan X96S MASS FLOW GAUGE Manuel d'utilisateur Page 39
- Page / 77
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
35
Density
This menu contains the following items:
ITEM MEANING
Raw Counts Non-filtered counts from the detector
Raw Density Non-filtered density from the detector
%Density Shows the percent of density based upon the min and max density range
Filt. Counts X96S filtered counts from the detector
Last Ref. Date Shows the date the last reference was performed
Ref Density Shows the actual value of the last density reference performed
Cal Density Shows the actual value of the last density calibration performed
Decay Ref Cap Shows the value of the reference captured counts
Decay Cal Cap Shows the value of the calibration captured counts
Ref Cap Shows the captured counts for the last density reference performed
Cal Cap Shows the captured counts for the last calibration performed
1/uT Shows the calculated slope value (multiplier)
Flow Rate
This menu contains the following items:
ITEM MEANING
Flow Rate Counts Rate of flow (example: feet per second)
% Flow Rate Shows the percent of flow rate based upon the min and max flow rate range
Low Flow Rate Shows the minimum flow rate value
High Flow Rate Shows the maximum flow rate value
Ref.Capt.Value Shows the captured counts for the minimum flow rate referenced
Cal.Capt.Value Shows the captured counts for the maximum flow rate for the last calibration
performance
Pulse Factor Shows the user the Pulse per flow rate (L/s) value
Solids
This menu contains the following items:
ITEM MEANING
Lo Solids Cap Shows the low value solids captured counts
Hi Solids Cap Shows the high value solids captured counts
Solids Counts Shows the current solids counts
Curr. Solids Shows the current solid density value being used for calculating the percent solids.
Min Solids Shows and allows the user to set the minimum solids range
Max Solids Shows and allows the user to set the maximum solids range
Alarms
This menu contains the following items:
ITEM MEANING
Sys. Alarm Shows the status of the system alarm
Det. Fault Shows the status of the detector
AutoCal Ref Shows the status of auto cal reference
AutoCal Error Shows the status of the auto cal error function
Ref. Prompt Prompts the user to complete the next reference
Wipe Test Notifies the user when to conduct the next wipe test (if relay is used)
Shutter Test Notifies the user when to conduct the next shutter test (if relay is used)
Alarms Shows the status of the activated alarm
Dig. Inputs Shows which digital input is in alarm
- MASS FLOW GAUGE 1
- Table of Contents 2
- Overview 5
- Basic Concepts 6
- Theory of Radiation Gaging 7
- Principles of Operation 8
- Menus/Operation 10
- [enable/disable] 11
- [Enable/Disable] 12
- [number] 12
- [seconds] Slot 2 12
- [type] Output 14
- Figure 3-4 Calibration Menu 15
- Figure 3-5 – Diagnostics Menu 16
- Variable Mapping Menu 17
- Status Display Menu 18
- Display Totalizer 19
- Operation Menu 19
- Density Filtering Menu 20
- Flow Rate Filter Menu 21
- Empty Clamp Menu 21
- Detector Fault Menu 22
- Temp Comp Menu 22
- Linearization Menu 23
- Scan Time Menu 23
- Mass Flow 23
- Solids Setup 25
- Flow Rate 25
- Proc Temp 25
- Head Temp 26
- Remote Totalizer Menu 27
- PD Counter 27
- Auto Reference 28
- Hardware 29
- System Hardware 29
- Source Type 30
- Next Shutter Test 30
- Flow Rate Hardware Menu 30
- Solids Adj. Hardware 31
- Analog Out Cnfg Menu 31
- HART Output 31
- Com1 Protocol 31
- Digital Outputs Menu 32
- Calibration 34
- Cal Remote Solids 34
- Ref Constants 35
- Low Reference (Cal Flow Rate) 36
- Temp Reference 37
- Loop Config Menu 37
- Aux Loop Cfg Menu 38
- Diagnostic 38
- X96S Local Display 40
- Editing Values 41
- Installation 42
- Handle Padlocked OFF 43
- Plunger Padlocked OFF 43
- Rod Padlocked OFF 44
- Lock Tag 44
- Safety Precautions 45
- Mechanical Mounting 46
- LOCAL CODE 47
- NATIONAL CODE 47
- Microprocessor Verification 48
- F1 F2 F3 F4 49
- Password 50
- Calibration Constant 52
- Calibration Curve 53
- Important facts to remember – 54
- Ronan Engineering 55
- X96S Mass Flow Gauge 55
- ABORT OK 56
- ESC ENTER 56
- High Density Calibrate 57
- Step 1 High Calibrate 58
- Low and High Flow Calibration 60
- Low Flow Reference 60
- (Have a “0” flow input ready) 61
- High Flow Calibration 62
- Configuration 64
- Detector 65
- ION Chamber 66
- Detector Housing 67
- Cable Connector 67
- Electronics 69
- X96-2009PL1 70
- X96-2009PL2 71
- X96-2009PL3 71
- MODEL X96S 73
- SAMPLE DRAWINGS 74
- Outline/Assembly 75
- Mounting Plate 76
- 21200 Oxnard Street 77
Produits connexes et manuels pour Équipement Ronan X96S MASS FLOW GAUGE
(3 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.448 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels